[Hands-On Review] Griot’s Garage 6 Inch Polisher (GG6) After 4 Years Use
// We may earn a commission if you make a purchase through links on this site. Read our Earnings Disclosure to learn more.
NOTE: This polisher has been discontinued and replaced by the Griot’s Garage G9 6″ polisher with improved ergonomics and a 9mm throw (versus the 8mm on the GG6) and more powerful 1000w motor.
After using the 3rd generation Griot’s Garage 6 Inch Dual Action Polisher, which I like to refer to as the GG6, for about 4 years now I thought it might be helpful to do a review to share with everyone. I’ve used the polisher way more than I originally intended to when I purchased it (and believe you will too) and have become intimately familiar with all of its ups and downs.
After all these years it’s still my favorite polisher and I wouldn’t hesitate to buy it again.
What’s Included
I originally purchased my GG6 from Advance Auto for around $100 using a ridiculous $40 off of $100 coupon I found online. I honestly don’t know if you can do this anymore. If not, you can’t find it for a deal here at Amazon. I purchased the (new then) 3rd gen version of the polisher with the 10-foot power cord (because I already own a sweet 100ft 14ga extension cord).
When I received the polisher it came in a box like this:
Inside the box was the following:




You’ll note there is:
- The polisher itself in all of its red plastic and black rubber glory
- Removable handle
- 6” backing plate with hook and loop (Velcro)
- Flat wrench for tightening the backing plate to the polisher’s spindle
- Allen wrench for installing the handle
- Bag with spare brushes for the electric motor inside the polisher
- Instructions (which are pretty good I might add).
Specifications
- Powerful 850-watt, 7-amp motor
- 8mm throw orbit
- 2500-6800 orbits per minute
- 10-foot 18 AWG, or 25-foot 16 AWG power cord
- Domed, rubberized palm grip
- 6 speed settings via dial, 1/2-speed increments
- 5lb 3oz weight
- Made in China
- Lifetime Warranty
The Good
Weight
The first thing I noticed when I purchased this polisher was the weight. At 5 lbs 3 oz it felt right to me. It’s enough to feel substantial and stable while using it without being too much that it wears you out on vertical panels.
Since using the polisher, my feelings about the weight remain the same. I’ve also used and compared other polishers and still don’t feel like there are any shortcomings in this category for the GG6.
Vibration
Out of all of the standard Porter Cable style polishers that I’ve used this polisher is the smoothest to me. I cannot tell a discernible difference in the vibration when running the 6″ backing plate or the 5″ backing plate that I often run. Admittedly this may be due to the 5″ plate being a little ticker and likely weighting close to the same.
If you plan to compare any polishers side by side make sure you have a pad and backing plate installed otherwise the vibration will be off the charts due to the counter weight on the spindle.
In my experience, to get a smoother DA than the GG6 you’ll need to step up to one of the long throw polishers like the Griot’s Boss G21 or Rupes Big Foot. They cost a lot more and can’t work as tight of spaces but they are smoother and cover more area faster.
Noise
This is the main reason I bought this polisher when I did. It was said to be a fair bit quieter than the competition, namely the Porter Cable xp7274 and Harbor Freight DA at the time. I’m happy to report that was true. For a standard Porter Cable style DA polisher this one is definitely the quietest by a large margin.
Is it quiet? No, I still wear ear plugs after speed 3. It’s simply the quiet-EST of the bunch.
Power
The GG6 is advertised as the most powerful of the standard or short throw polisher and it sure feels like that’s true. Though the truth is that if you’re using your polisher correctly any of the DA polishers available are powerful enough to get the job done in the same amount of time. It’s nice to have the power on tap though.
Heat
You would think since this tool generates more power that it would also generate more heat. Fortunately, the polisher stays cool to the touch no matter how long I run it. The motor vents air out of the side of the body on both sides, which is nice because you don’t get a face full of hot air when you’re working up close in tight spaces.
I do have to be careful of overheating pads, due to in part to the extra power of the tool. If your speed is too high, your pad is too wet, and your pressure is too much, you can quite literally melt the pad and backing plate where they stick together. This is not a fault of the tool, just something to be mindful of with any DA style tool since they tend to generate heat where the pad and backing plate stick to eachother. It’s just more pronounced in more powerful tools.
Ergonomics
For me, I like the rubber palm grip hand holds and finger grooves. They really do help me hang onto the polisher while working all the weird angles I run into when working on cars and random parts. I don’t use the handle (I don’t on any polisher because I don’t feel like I have as much control) so the rubber grips really come in handy. If you’re a handle user, it has a rubber grip on it as well.


The power switch is located on top of the unit toward the middle and is easy to reach with your thumb or index finger to turn on or off while the polisher is held against the paint. This is good because you never really want to turn on a DA when it’s off the surface of the paint because it’s quite unstable and will fling polish everywhere.
The speed switch is located on the top of the unit toward the bottom. It’s a little cumbersome to turn the speed up or down while using it but it keeps you from bumping it accidentally while using it, which I personally feel is more important.

Versatility
I’ve used this polisher on everything from paint on automobiles to plastic lenses to glass and it always works. I’ve even seen some people use it for sanding though Griot’s recommends not to do that. With the right pad and polish I’ve polished out 1500 grit sanding marks in both clear coat and plastic. At the end of a correction I also use it to apply wax if I’m not putting on a paint coating.
What I’m getting at is this polisher can do it all and, with how
