Ultimate Beginner’s Guide to Car Buffers
// We may earn a commission if you make a purchase through links on this site. Read our Earnings Disclosure to learn more.
There are few areas in auto detailing that are as misunderstood than that of machine buffers and polishers. Anyone who has researched polishers in the hopes of learning the trade has at one time sat there scratching their head trying to understand the differences between each machine and which one would be the best for the task at hand.
I can’t fault anyone for that given that there are so many different options available that get referred to, often incorrectly, by many different names.
My hope for this guide is to break this information down into easily digestible chunks so that you can make sense of it all and know exactly what tool you should start with for whatever job you’re wanting to tackle.
Why Machine Polishers Exist
Traditionally people would work polishes into paint and apply waxes by hand. While this worked reasonably well with old single stage lacquer and urethane paints it’s is much more difficult on today’s very hard and very delicate multi part clear coat finishes.
Working a polish into a clear coat to remove scratches can work but it’s a lot of work. The larger the area you have to polish the more unrealistic working by hand becomes. Some clear coats are so hard that it’s neigh impossible to reach a fully defect free finish by hand.
The solution? Machine polishers. Not only are they more powerful than your hands they are much more efficient. They save us that which is most valuable. Time!
Buffers vs Polishers
In the most simplistic terms, buffing and polishing mean the same thing. It’s the act of working a product such as a polish into a surface to alter the appearance of the surface. If you look up the definition of buff it means to polish. That means buffers and polishers are one in the same as well. They are simply two different names for the same tool.
You’ll see me use both words when describing each machine simply because some people may be more familiar with one term over the other and I want everyone to find this information useful.
Basic Construction of an Automotive Paint Machine Polisher
There are four main parts to a modern polisher. There is the the motor, the spindle, the backing plate, and the pad.

Polisher Motor
- Variable speed motor that drives the spindle.
- Can be pneumatic (run on compressed air) or electric
Polisher Spindle
- Rotating spindle attached to motor that holds the backing plate.
- Sometimes free spinning and sometimes fixed drive.
Polisher Backing Plate
- Rubber or plastic plate that attaches to spindle and holds the pad.
- Often flexible.
- Sometimes has hook and loop (velcro) on one side to hold polishing pads.
Polisher Pad
- Holds the polishing compound.
- Can be made of foam, microfiber, wool, or a combination of them all.
Types of Machine Polishers
There are two primary types of buffers and polishers: Rotary and Orbital. These terms mostly refer to how the pad rotates around the motor. With a rotary buffer the spindle and pad rotate together in one direction. It doesn’t vibrate, oscillate, or orbit. With an orbital polisher the spindle and pad move about different axis causing the pad to vibrate, oscillate, or orbit (much like the Earth around the Sun).
Beneath the Orbital type of polisher there are sub types of Fixed Orbital, Dual Action Random Orbital, and Dual Action Forced Rotation. The differences between these types is explained below.
Rotary Buffer

Appearance
- Most resemble an angle grinder because that is what they evolved from
- Some include a fixed or removable handle to one side or another
- Most USA made rotary buffers will have a 5/8″ diameter 11 threads per inch sized male arbor on the spindle that the backing plate screws onto
Function
- Circular rotation with axis at the center of the spindle
- Rotates in single direction
- Directly driven by motor
- Variable Speed
- Outer diameter of pad spins faster than inside diameter

Uses
- Fast removal of moderate to heavy swirls, defects, and sanding marks
- Can be used for spreading wax but not a common practice
Pads
- Used with wool, microfiber, and foam pads though wool and foam are the most common
- Larger pads are more aggressive due to increase outer diameter speed
- Pad size doesn’t affect machine performance
- No color standard between pads and types
Risks
- Pad friction with paint generates heat
- Heat generated between pad and paint is great at pad edge
- Cutting performance is greater at edge of pad
- Burns, swirls, and holograms are easily created if too much pressure is applied or edge of pad stays in one place too long
- Faster material removal means its easier to waste clearcoat and paint
Difficulty
- Learning to use tool properly takes time
- Chance of damaging paint while learning is high
- Perfecting use of tool takes practice
Orbital Polisher

Appearance
- Similar appearance to dual action sanders
- Some have handles over the top, out the side, or are simply covered in a grippy rubber
- Most USA made DA style Orbital Polishers use a 5/16″ diameter 24 threads per inch female threaded hole that the backing plate screws into
Function
- Pad and backing plate spin at different axis than the spindle
- Pad and backing plate rotation can be forced or free spinning (or both!)
- Variable speed

Uses
- Commonly used for light to moderate defect removal. Advances in pads and compounds have made heavy defect and sanding mark removal possible as well.
- Wax application and removal
Pads
- Most commonly used with foam and microfiber pads
- Bonnets can be placed over pads for removing polishes and wax
- Vibratory motion generates heat between pad and backing plate
- Larger pads reduce machine performance leading to less aggressiveness
- No color standard between pad brands and types
Risks
- Risk are greatly reduced over rotaries due to pad motion
- Pressure on a free spinning orbital slows pad down so risk from excess pressure and speed is greatly reduced
- Aggressive pads combined with aggressive compounds can leave behind micromaring but it’s very hard to do any real damage or to waste any clear coat
- Burning through paint is highly unlikely, especially on flat surfaces
Difficulty
- Learning to use the tool safely only takes a few minutes
- Chance of damaging paint while learning is low
- Perfecting use of the tool takes much less practice than a rotary
Types of Rotary Buffers
Not much has changed in rotary tools and technology. Almost all rotaries are derivative of angle grinders and look the part. The motor is in the body of the polisher at a right angle to the spindle. There are only a couple varieties that place the motor above the spindle
Regardless of appearance and age they all function the same. The motor turns the pad and backing plate in a perfect circle with the option of variable speeds.
The differences between brands are simply differences in tool weight, minimum and maximum speed, and ergonomics (location and shape of handle and grips and triggers).
Any differences in price merely reflect the tools power and reliability.
There are also a couple companies that sell adapters to turn power drills and other tools into pseudo rotary buffers. These actually work quite well because of how simple the operation of a rotary is and they are equally as risky to use.
I have written an article listing the best examples of quality rotary polishers on the market today.
Examples of Rotary Polishers



Types of Orbital Polisher
As stated before, there are three main sub-types of orbital tools. There is the Fixed Orbital, Dual Action Random Orbital, and Dual Action Forced Rotation
Fixed Orbital Polishers

If you’ve ever walked down the automotive cleaning and detailing isle at any big box store you’ve probably seen these on the bottom shelf for $20 or so.
Commonly referred to as “Wax Spreaders,” these orbitals are recognizable by their top mounted motors. Most have almost a bell shape to them. They are sometimes labeled as “Random Orbital Polishers.” They are typically low amperage, low speed tools. The pad on them is large and oscillates around a fixed axis to mimic the motion of hand waxing rather than spinning like most other orbitals and all rotaries.

The pads on these tools aren’t usually removable and instead rely on bonnets that are placed over the pad.
While these tools work great for applying and removing waxes and sealants they aren’t great at compounding and polishing. Their low power, speed, and lack of rotation inhibit their ability to remove anything other than superficial defects. The vibration caused from the oscillating pad is also quite uncomfortable for long periods of use.
If you are trying to perfect the surface and appearance of your paint I suggest you move on to the dual action random orbital polishers.
Examples of Fixed Orbital Polishers:

Dual Action Random Orbital Polisher
Affectionately referred to as DA Polishers, DA Buffers, or Random Orbital Polishers these are the most common machine polishers for compounding and polishing clear coat paints. They are used by both novices, hobbiests, and professionals alike.
Related: In-depth Look at the 12 Best Corded Dual Action Polishers
You can identify a dual action random orbital polisher by their resemblance to DA sanders. The spindle is typically mounted perpendicularly to the motor and is much larger due to the counterweight that is necessary to balance out the action of the polisher.
Why are they called Dual Action?
These polishers
